Siglent SHS810X – Handheld Digital Oscilloscope (2 Ch, 100 MHz)

• 2 channels, 100 MHz bandwidth
• Sample rate of 1 GSa/s (single-channel), Sample rate of 500 MSa/s (two-channels)
• Waveform capture rates up to 100,000 wfm/s (normal mode) and 4 00,000 wfm/s (sequence mode)
• True RMS Multimeter
• IP51 waterproof and dustproof

SIGLENT’s Handheld Digital Oscilloscopes include the SHS800X and SHS1000Xmodels. Both feature2 analog oscilloscope input channels are available in 200 MHz and 100MHz analog bandwidths, a single ADC with 1 GSa/s maximum sample rate, and a single memory module with 12Mpts memory depth. When two channels are enabled, each channel has a sample rate of 500 MSa/s and a standard record length of 6Mpts. When only a single channel is activated, the maximum sample rate is 1 GSa/s and the maximum record length is 12Mpts. For ease of use, the most commonly used functions can be accessed with its user-friendly front panel design.

The SHS800X series has two non-isolated scope channels and one isolated multimeter channel.

The SHS1000X series features full isolation between the two oscilloscope channels, one multimeter channel, a power adapter, and the USB host/device port. The full isolation makes it ideal for both laboratory and floating signal measurement because it reduces the risk of accidental short circuits.

The SHS1000X series features full isolation between the two oscilloscope channels, one multimeter channel, a power adapter, and the USB host/device port. The full isolation makes it ideal for both laboratory and floating signal measurement because it reduces the risk of accidental short circuits.

The SHS series utilizes a new generation of SPO (Super-Phosphor Oscilloscope) technology that provides excellent signal fidelity and performance. It comes with a vertical input range from2mV/div to 100V/div, and a max offset range up to 400V.

The innovative digital trigger system delivers high sensitivity and low jitter, and a waveform capture rate of up to 400,000 frames/sec. The SHS also employs a 256-level intensity grading display function and a color temperature display mode for clarity and fast fault identification.

The SHS’ have multiple powerful triggering modes including serial bus triggering as well as free decoding for IIC, SPI, UART, CAN, and LIN bus types. The SHS models also include History waveform recording and sequential triggering that enable extended waveform recording and analysis. Another powerful addition is the new 1 million point FFT math function that gives the SHS very high-frequency resolution when observing signal spectra. The new digital design also includes a hardware co-processor that delivers measurements quickly and accurately without slowing acquisition and front-panel response.

The SHS series feature built-in sample and measurement value recorders. The sample recorder can achieve a maximum sampling rate of 25kSa/s and can record for up to 22 hours at this sampling rate. The measurement value recorder can simultaneously record 4 sets of measurement values at a recording interval as low as 0.1swhich delivers up to 25 hours of continuous recording.

The SHS series integrates a 6000 count digital multimeter, isolated from the scope that can measure DC/AC Voltage, DC/AC Current, Resistance, Capacitance, Diodes, and Continuity.

A rechargeable 6900mAh lithium battery supports up to 5.5 hours (4 hours SHS1000X)of work without a charge.

The handheld oscilloscopes feature sealed IP51 dust and drip-proof housing and have been tested to IEC60529to guarantee the ruggedness that is needed to survive harsh environments. A rubberized surface with large keys also makes it easy to use in difficult environments.

Large bright 5.6-inch TFT -LCD display with 640 * 480 resolution. The most commonly used functions are accessible using 8 different one-button operation keys: Run/Stop, Auto Setup, Default, Cursor, Measure, Display/Persist, Clear Sweep, and Print. More function shortcuts are available combined with the shift button.